Vaio (diverse) Vaios mit InsydeH2O Bios: BIOS freischalten + VT aktivieren

Hey Speed gibt es das Bios nur für sony od. auch für dell.
Ist halt nur mal aus interesse gefragt.
Da ja unter sony das mit dem VT nun ja geht.
Würde mich interessieren ob es wenn es denn für dell sowas gibt auch ne möglichkeit gibt da dann Memory Remapping zu aktivieren od. deaktivieren.:D

Da muss ich passen. Ich habe seit 10 Jahren nichts mit Dell Orodukten zu tun.
 
Die beiden anderen "aktuellen" Bios Varianten sind Phoenix und AMI Aptio. Und die unterscheiden sich auch deutlich.
TDO


hi

gibt es auch schon was für das AMI Aptio bios?
Möchte gern das advanced menu haben

Gibt's beim freigeschalteten Bios irgendwelche Einstellungen die das "Battery-Leak" Problem erklären oder beheben können)?

was ist denn das battery-leak?


mfg & danke
 
hi

gibt es auch schon was für das AMI Aptio bios?
Möchte gern das advanced menu haben



was ist denn das battery-leak?


mfg & danke

battery leak ist ein phänomen, dass akkus (auch neue) die im gerät stecken nach 4-5 tagen (oder kürzer) komplett entleeren obwohl das gerät ausgeschaltet ist - wenn das gerät nicht eingesteckt ist. aber gut, dass du mich daran erinnert hast, jetzt werde ich gerade wieder sauer auf sony!!! :mad:
 
ok
danke für die antwort
dann kenn ich das problem auch (nur nicht erst nach 4tagen, sondern eher)
die batterie, wenn sie aus dem laptop raus ist bleibt aber dann vollgeladen
 
ok
danke für die antwort
dann kenn ich das problem auch (nur nicht erst nach 4tagen, sondern eher)
die batterie, wenn sie aus dem laptop raus ist bleibt aber dann vollgeladen
ja genau..das ist es...kann auch durchaus kürzer sein und ist bei mir mittlerweile der grund warum ich allen freunden, bekannten und geschäftspartnern von sony notebooks abrate. :(
 
Ok, das is mega komplex

Hi Leute,

ich habe mir mal die Anleitung durchgelesen aber so ganz schlau werde ich da net. In meinem Bios, kann ich VT oder wie das heißt anschalten. Zumindest habe ich die option da.
Was mich viel mehr nervt und daher interessiert ist, wie man das Bios in sienern ganzen Funktionalität freischaltet.
Ich habe mich imme rgewundert wieso man so wenig einstellen kann und bin erst durch den thread drauf aufmerksam geworden, dass man das wohl frei schalten kann.

Ich besitze das VGN_Z21wn/b mit win7 64bit , 8Gig Ram und SSD drive.

Zugegeben bin ich nicht ganz bewandert was das proggen und so angeht. Könnte mir da vielleicht noch mal wer helfen.?

Achja und hat einer von euch GPS zum laufen bekommen? Habe gehört die Vaios haben GPS funktionalität über das WWAN Modul?

Danke und bis später :)
 
Hi Leute,

ich habe mir mal die Anleitung durchgelesen aber so ganz schlau werde ich da net. In meinem Bios, kann ich VT oder wie das heißt anschalten. Zumindest habe ich die option da.
Was mich viel mehr nervt und daher interessiert ist, wie man das Bios in sienern ganzen Funktionalität freischaltet.
Ich habe mich imme rgewundert wieso man so wenig einstellen kann und bin erst durch den thread drauf aufmerksam geworden, dass man das wohl frei schalten kann.

Ich besitze das VGN_Z21wn/b mit win7 64bit , 8Gig Ram und SSD drive.

Zugegeben bin ich nicht ganz bewandert was das proggen und so angeht. Könnte mir da vielleicht noch mal wer helfen.?

Achja und hat einer von euch GPS zum laufen bekommen? Habe gehört die Vaios haben GPS funktionalität über das WWAN Modul?

Danke und bis später :)

Hab das mal noch ausgegraben ;-) Jemand Erfahrungen?

Re: Vaio TZ GPS, how can I enable it?
To dig this thread up from long time ago, but I have found an interesting thing with regard to GPS:

Yes, GT modem has GPS built-in and it's true GPS. There is a way to use hyperterminal / Putty to enable it. My Vaio TZ comes with GTM378 module and I was able to follow this guide to enable GPS:

http://www.option.com/en/support/kno...articleen-175/

However there is one very annoying thing. Once the GPS is enabled, the COM port starts to scan for locations and output NMEA-standard code.

As for me, reinstalling laptop works, because of the sony-provided drivers on their website. As long as you install their driver, it works. If you try to install the vendor's driver it doesn't work anymore. It's very annoying.

Way to install GlobeTrotter 2.3 and up (because it has SMS functionality which sony-provided GlobeTrotter 2.2 doesn't): Install GlobeTrotter 2.2 first. Then go into c:\Program Files\Option\GlobeTrotter Connect\driver and copy the folder GTHSDPA and save it anywhere. Then install GlobeTrotter 2.3 or 3.0 depending on what you get. Then copy back the folder GTHSDPA into driver. Then open up any driver that is undetermined by windows and set it to update to the path of GTHSDPA folder as it contains all the drivers needed.

Quick guide to enable GPS:
1. Go to Device Manager, look under Port/Com for GlobeTrotter Module HSDPA Application Interface COM[X], and Application 2 Interface COM[Y] (X and Y are numbers)
2. Open Hyperterminal or Putty, make a serial connection to COM[Y]
3. Type ati in PUTTY windows see if it returns your vendor and firmware version. If it does then it works. If it doesn't then try look for the right COM
4. on COM[Y] windows type AT_OIFC? see if it returns something looking like:
_OIFC x,y,z,w where x,y,z,w are numbers. w has to change but remember the first 3.
5. Type AT_OIFC=x,y,z,2 to enable GPS. try 5 first, sometimes it doesn't allow 5. (2 means GPS-enabled. 3 means Application 2 Interface enabled. 5 means both of them enabled).
6. Restart the modem by toggling it on/off or restart computer. If 5 was enabled earlier you should see an extra COM is being installed, depending on if the driver can fit it or not then install the driver and go check the COM number (COM[Z]). if only 2 is enabled then you should see nothing extra.
7. Now use Putty to connect to COM[X] mentioned earlier. This is where you issue the commands (Application Interface). Try typing ati on this see if it returns the firmware version. Use Putty to connect to COM[Y] mentioned earlier as well, but you should notice that you can no longer type commands in COM[Y]. This is because COM[Y] has turned from application 2 interface into GPS output.
8. In COM[X] type AT_OGPS? it should return _OGPS = 0
9. If it does, you can issue 3 commands below to get some output:
AT_OGPS=0 This means you stop GPS
AT_OGPS=1 This means you turn on GPS device to determine your location. It will stop when it finishes locating your position that one time, or it returns an error.
AT_OGPS=2 This means you turn on real time GPS tracking. It will try to determine your location, but it doesn't stop scanning.

Now you can connect your programs of choice with COM[Y] for more GPS information. Note that it is in NMEA format so connect the software which supports that standard and you should be able to locate yourself. There are 2 things I am unsure of:

1. Whether there is any GPS antenna attached to the card's GPS slot or not or
2. If the GPS device works without an antenna and how strong/weak the signal would be.

I have yet to be able to implement software in the COM port successfully yet, so anyone else who would like to try this and post the results would be appreciated.

Thanks for reading. Hope you find it interesting.

EDIT: I found out that the modem conflict was simply because of the wrong COM port selected. If you open your device manager and found that there is a conflict which makes you unable to start any of the COM device (including the modem), simply select another COM port for them and it should start correctly. Also check out my guide to update firmware http://forum.notebookreview.com/show...postcount=1164
__________________
Click here to find out how to enable 7.2 mbps capability of WWAN Sony Vaio TZ with GTM378 module.

Click here to find out more about enabling GPS Sony Vaio TZ with GTM378 module.
 
ich habe mir mal die Anleitung durchgelesen aber so ganz schlau werde ich da net. In meinem Bios, kann ich VT oder wie das heißt anschalten. Zumindest habe ich die option da.
liegt wohl daran, daß der Thread uralt ist :rolleyes:

Was mich viel mehr nervt und daher interessiert ist, wie man das Bios in sienern ganzen Funktionalität freischaltet.
Ich habe mich imme rgewundert wieso man so wenig einstellen kann und bin erst durch den thread drauf aufmerksam geworden, dass man das wohl frei schalten kann.
was genau vermisst du? die allermeisten Optionen sind im Notebook nicht wirklich erforderlich und übrlicherweise im BIOS nicht einstellbar. Auf den eingangs geposteten Screenshots sehe ich nicht viel, wozu ich denken würde "Mensch, das hab ich schon immer gebraucht" :rolleyes:
 
Da muss ich passen. Ich habe seit 10 Jahren nichts mit Dell Orodukten zu tun.
Hallo habe ein HP Pavilion Dv6 3010sg mit dem gleichen Bios(Insyde H2O Rev. 3.5 F.23)
Würde bei mir gerne die gleichen Bios-Funktionen aktivieren.Bräuchte aber Hilfe.

(Ich kann alles essen,aber nichts alles wissen!)

Gruß Daddel
 
Ich muss den Thread jetzt auch mal nutzen.

Ich habe ein Sony Vaio VPC YB1S1E mit AMD E-350 APU das mit einem InsydeH2O Bios Rev 3.5 ausgestattet ist.

Ich habe das Notebook schon aufgeschraubt und die verwendeten Wärmeleitpads und die relativ schlechte Wärmeleitpaste ausgetauscht und mit dem Brazzos Tweaker untervoltet und so meine Temperaturen um bis zu teils 10°C senken können in der Hoffnung das Sonys Lüftersteuerung endlich Ruhe gibt und den Lüfter nur ganz langsam läuft bzw dieser mal im Idle einfach still steht.
Pustekuchen. Trotz mehr als angenehmen ~ 45-48°C im Idle und "kühler" Luft aus den Lüftungsschlitzen läuft der Lüfter immer noch hochtourig.

Ich gehe davon aus das der Freischaltcode auch für das AMD Modell gilt. Aber die Frage ist: Kann ich im BIOS irgendwie die Lüftersteuerung einstellen?
 

Ähnliche Themen

Vaio Z Raid freischalten bei neuem Bios R4041M3b

Vaio (diverse) Kompletter Windows 7 Installations Guide (gilt auch für Vista)!

Zurück
Oben